DFM-24
Back to "Products"Voltage transformer for indoor application designed in accordance with the prescriptions of the DIN 42600-9 standard.
General Description
The support type voltage transformer, consists of primary (medium voltage) and secondrary (low voltage) windings, built concentrically on a fully epoxy resin embedded link type core, produced of cold rolled grain oriented electrical steel is manufactured in single pole design on a coated metal baseplate. The windings and the terminals are made of copper.
The voltage transformer is suitable for indoor application for rated primary voltages from 15kV to 24kV, that is for maximum system voltages from 17,5kV to 24kV.
For supplying protective relays or other appliances. The secondary winding can be for measurement purposes, protective (for relays) or for produce residual voltages (earth fault signaling) or the combination of these. The accuracy classes for measurement can be 0,2, 0,5, 1 or 3, for protection 3P, 6P and for the winding for residual residual voltages 6P, and the instrument can be made with 1,2 or 3 secondary circles.
The voltage transformer is designed and manufactured to comply with the requirements of the effective Hungarian Standards MSZ EN 61869-1,-3 or EN 61869-1,-3, the previous MSZ EN 60044-2, IEC 186 and also with the DIN 42600-9. On the basis of common agreement it is also possible to manufacture according to other standards different from the aforementioned.
Packing, delivery
The current transformer is delivered in a finish suitable for use under normal climatic conditions, packed in corrugated paper boxes. Upon common agreement the delivery can be made in finish and packing suitable for the requested climatic zone.
Installation, operation
The voltage transformer can be installed by means of 4 pcs M10 bolts. The connection to the terminal of the primary winding can be accomplished by an M10 bolt. The earth terminal of the primary coil is located next to the secondary terminals and to this the connection can be made by a wire with cable lug, sized for M5 bolt.
The size of the bolt used for the connection of the protective earthing is M8 and it is located on the side opposite to the secondary terminals. If necessary the ends of the secondary windings, marked with „n” can be earthed to the baseplate by an M5 bolt.
The plastic ratingplate is located above the secondary terminals and it contains the marking of the terminals as well. The secondary terminals are provided with a sealable plastic cover.
All the bolts and washers are coated. The earthing of the voltage transformer is obligatory. The earthing of the secondary windings must be accomplished in accordance with the effective local requirements.
Operation is possible keeping the prescriptions of the relevant security – labour – and property – protection directives. Any faults and breakdowns emerging in the costumers sphere of interest due to breaching, disobeying the aforementioned, exemt the manufacturer from the warranty and quarantee lialibities.
Maintenance
The maintenance consists of works to be done according to the general rules for maintenance of indoor instrument and equipments. These are:
- periodical inspection of contamination
- cleaning depending on the degree of impurity
- inspection of the surfaces
- tightening the bolts of the primary and secondary connections
- tightening the fastening and the earthing bolts.
State verification
The secondary windings of the current transformers in class 0,2, 05, are manufactured in finish suitable for verification. The verification will be made only on special request. In this case it will be accomplished and documented by an official seal or an affixed verification stamp by the state office for measurement.
Data to be supplied with the order
- type
- rated insulation level
- rated primary and secondary voltages
- number, accuracy class, output of the secondary windings
- voltage factor
- quantity
- requested term of delivery
Other or special requirements
- climate zone of use other than normal
- language of the rating plate
- packing
- number of pieces and sort of the documentation requested
Warranty period, guarantee
The warranty period is 12 months. Upon mutual agreement of the parties it can be otherwise established.
Technical data
Rated voltage (network) | 15 kV 20 kV |
Highest voltage for equipment | 17,5 kV 24 kV |
Rated primary voltage
Rated secondary voltage |
15000/√3-22000/√3
100/√3, 110/√3 |
Power frequency withstand voltage(r.m.s.) | 38 kV 50 kV |
Lightning impulse withstand voltage (peak) | 95 kV 125 kV |
Accuracy class measurements
protection |
0,2,-3
3P, 6P |
Winding to produce residual voltage ( earth fault signaling rated voltage
output accuracy class |
100/3V 110/3V 25VA 30VA 6P |
Power limit of the voltage transformer | 400VA |
Voltage factor | 1,9Un/ for 8 hours operating time |
Insulation class | B |
Number of circuits which can be verified | 2 |
Dimensions (lxwxh mm) | 385x178x280 |
Mass(kg) | ~32 |
Rating Plate
- material: plastic
- dimensions: 01 x75 x 90 mm
- markings: printed
Accuracy classes of the different rated outputs
One circuit
Output VA | 5 | 10 | 15 | 25 | 30 | 50 | 75 | 150 | 200 |
Accuracy class | 0,2 | 0,2 | 0,2 | 0,2 | 0,2 | 0,5 | 0,5 | 1 | 1 |
Two circuits
Maximal secondary loading current (Imax)